HPE6-A89 시험 - HP실제시험문제와 답 - 90문항

Question No : 1

What is the primary purpose of using multiple OSPF areas?

A.To reduce the size of the routing table and improve scalability
B.To increase packet forwarding speed
C.To allow static routes to take priority over dynamic routes
D.To enable NAT for internal networks

정답:

Question No : 2

Scenario: A junior network engineer configures a user account on a Comware switch but forgets to assign a privilege level. The engineer reports they cannot execute administrative commands after logging in.
What is the likely cause?

A.The switch is in user view mode only
B.SSH key was not imported
C.The user is at privilege level 1
D.No console port is available

정답:

Question No : 3

Scenario: An administrator is configuring a new HPE Comware switch. After connecting via the console port, they want to enter the system view to begin configuration.
What command should the administrator use?

A.enable
B.configure terminal
C.system-view
D.admin

정답:

Question No : 4

Scenario: Your customer wants to limit YouTube traffic to 2 Mbps on a specific uplink port but allow all other traffic without restriction.
What configuration approach should be used?

A.Enable storm control
B.Set global QoS policy for all interfaces
C.Classify YouTube traffic by IP or port, and apply CAR rate-limit
D.Change the PVID for the uplink port

정답:

Question No : 5

Which command tests basic IP connectivity from a Comware switch?

A.traceroute
B.ping
C.display ip route
D.ip test

정답:

Question No : 6

What is the default user privilege level when accessing a Comware device via the console port?

A.Level 0
B.Level 1
C.Level 2
D.Level 3

정답:

Question No : 7

What must be configured after assigning a port to a VLAN in access mode?

A.PVID
B.Trunk tag list
C.VLAN IP address
D.Link aggregation

정답:

Question No : 8

What happens if no ACL rule matches a packet and there is no default permit statement?

A.The packet is forwarded
B.The packet is denied
C.The packet is logged and dropped
D.The packet is forwarded to the control plane

정답:

Question No : 9

Scenario: You have applied ACL 2001 on interface GigabitEthernet1/0/10 in the outbound direction. Users report blocked traffic even though you permitted their subnet.
What is the most likely cause?

A.ACL is applied inbound instead of outbound
B.ACL lacks a permit for specific destination IP
C.ACL does not have a permit ip any any as a final rule
D.Packet filtering is disabled globally

정답:

Question No : 10

Which of the following BGP attributes is mandatory in every route advertisement?

A.LOCAL_PREF
B.ORIGIN
C.MED
D.NEXT_HOP

정답:

Question No : 11

Scenario: You’re configuring a Comware switch to act as a DHCP client on interface Vlan-interface 100 to receive an IP address automatically from a DHCP server.
Which command must be applied within the VLAN interface configuration?

A.ip address dhcp
B.ip address dhcp-allocate
C.ip dhcp enable
D.address-mode dynamic

정답:

Question No : 12

Which command would you use to apply a QoS policy to an interface?

A.apply qos-profile
B.traffic-policy apply
C.qos enable interface
D.class-map bind

정답:

Question No : 13

Which command saves the current configuration to the startup configuration file in Comware OS?

A.write memory
B.copy running-config startup-config
C.save
D.commit

정답:

Question No : 14

Scenario: An enterprise is deploying OSPF in a multi-area design. One department is assigned to Area 10, and another to Area 20. Both connect to a central Area 0. They want to restrict Type 5 LSAs from entering Area 20.
Which area type should you configure for Area 20?

A.NSSA
B.Stub
C.Totally Stubby
D.Backbone

정답:

Question No : 15

Scenario: Two Comware switches are part of an IRF fabric. The master switch fails unexpectedly.
What happens next in the IRF topology?

A.The fabric shuts down
B.The backup switch takes over as the new master
C.All VLANs are disabled until recovery
D.Manual intervention is required to restore operations

정답:

HP HPE6-A89 시험